fog light install kits

Replies to This Discussion

Permalink Reply by the flea on December 19, 2008 at 11:51pm

OK , help me here, how hard it is to install a set of lights, wire a protected switch and make it work. WTF is the controller needed for? , why will you need to run the lights throught it?
Please Mr B.E post some pics of your mod.

flea

▶ Reply to This

Permalink Reply by mr bad example on December 20, 2008 at 2:21am

i haven't put in fog lights yet, is that you on the left?

▶ Reply to This

Permalink Reply by the flea on December 21, 2008 at 12:05am

now that's funny,,,,,no...I'm actually holding the camera..
...Please post some pics of your light and switch mod when done
...I know it will be top shelf...BTW seen your spud gun video....pretty cool

flea

▶ Reply to This

Permalink Reply by mr bad example on December 21, 2008 at 2:56am

you should see my new "mod" for the spud gun, 150,000V ignition, i'll make a video of that in a couple days, 1/2 inch hot blue spark (ARC), beats the hell out of a 1/16 inch piezo Weber sparker. (i left the weber on, just in case i run out of batteries in the field, i have three NiMH 9v batteries, so that should never happen)

▶ Reply to This

Permalink Reply by the flea 1 day ago

so. what are you going to blow up next?

flea

▶ Reply to This

Permalink Reply by mr bad example 1 day ago

i've got another monitor (12inch monochrome, my color ones i'll sell, i just bought 4 LCDs in the last 2 weeks) i got a new Grundig am/fm/sw radio coming in, i could blow up my GE classic radio (works fine, no light behind the dial though)

my smart "died" today, dead stick shift, so i can't drive off to blow anything up now. it's too damned cold, as you know, i'll take "donations" for other things to blow up, they have to fit in a smart.

▶ Reply to This

Permalink Reply by Not so smart on December 19, 2008 at 11:34pm

My smart center still says they don't know how to do it. Install the fog lights yes. Update the software no !

▶ Reply to This

Permalink Reply by mr bad example on December 20, 2008 at 3:52am

wouldn't your "smart center" qualify as a "brick and mortar" oxymoron?

▶ Reply to This

Permalink Reply by Not so smart on December 20, 2008 at 1:53am

It's not hard at all if you don't care about using the original on/off switch.Just mount a fused swiitch to a hot wire under the dash somewhere and tie into the fog light harness. But if you own a Pure and are a purist, and like your work to look and work like it would from the factory,they are making it harder then it should be. They should not make the car so you have to have a software update to turn on the fog lights with the factory switch. And then to top it off, not tell most of the dealers how to do it. It should just work ! Add the fog lights,plug them in, and turn them on. Thats it.

▶ Reply to This

Permalink Reply by Administrator on December 20, 2008 at 2:42am

I would like the original switch to work.

▶ Reply to This

Permalink Reply by Ian Pellant on December 20, 2008 at 4:08am

I'm sure we covered this before... it seems that the TAN Code (err... ECU or SAM programming ??) needs updating for the factory switch to be activated. See the last line of: http://www.fq101.co.uk/451foglamps.asp

▶ Reply to This

Permalink Reply by Ian Pellant on December 20, 2008 at 6:07am

... web searching for TAN code and I found this site: http://www.cardomain.com/ride/2078147
... a tuned roadster... ahhhh...!
But still no clue what a smart TAN code may be except a: Transaction Activation Number ?

▶ Reply to This

• 1
• 2
• 3